Parkside PSS 250 A1 Bedienungsanleitung Seite 10
- Seite / 68
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
10 GB
Operation / Maintenance and Cleaning / Service centre / Warranty / DisposalOperation
Sanding sheets without hook and loop
fastening:
Open the two clamping levers
7
.
Push one end of the sanding sheet
9
under the
open clamping bar
6
and clamp the sheet firmly
in place by locking the clamping lever
7
back
in place.
Repeat this procedure at the other end.
Various materials require different grit values. You
can read which grit value is best suited for which
work in our recommendations under “Instructions,
tips and tricks”.
Vacuuming dust
FIRE HAZARD! A risk of fire
exists when working with electrical appliances that
have a dust collection box
4
or can be attached to
a vacuum cleaner via an external suction adapter!
Under certain conditions the sanding dust in the dust
box (or in the vacuum’s dust bag) may self-ignite, e.g.
as a result of flying sparks generated when abrading
metals or metal objects left in wood. This can happen
especially if the wood dust has paint particles on it
or is mixed with other chemical substances and the
sanded material is hot after extensive working. You
should therefore avoid overheating of products be-
ing sanded as well as the appliance and always
empty the dust collection box
4
or the dust bag of
the vacuum cleaner before work pauses.
Wear a dust mask!
Vacuuming dust with the dust
collection box
Attach the dust collection box:
Push the dust collection box
4
on to the device.
Remove the dust collection box:
Press the release button(s)
3
and pull the dust
collection box
4
off the device.
NOTE: Always empty the dust collection box
4
in due time and shake any remaining dust out; this
will ensure optimal vacuum performance.
Dust extraction using an external
vacuum extraction device
Connecting:
For vacuum dust removal using a vacuum
cleaner, push the suction hose of a vacuum
cleaner approved for use as a dust extraction
device (e.g. a workshop vacuum cleaner) into
the connection
5
– see Fig. D.
NOTE: If it is necessary to use the reducer piece
12
, push the reducer piece into the connection
5
.
Removing:
Pull the hose of the dust extraction device off
the connection
5
or off the reducer piece
12
,
if one is used.
Instructions, tips and tricks
Move the oscillating sander parallel, in flat
circles or alternating between lengthwise and
side-to-side motions.
Do not press down with the oscillating sander.
The sanding sheets become clogged, which
reduces the sanding performance.
Clean the sanding sheet
9
occasionally with
the vacuum cleaner.
The removal performance and therefore the re-
sult of your work are determined by the correct
selection of the speed and sanding sheet
9
grit.
Never sand different materials with the same
sanding sheet
9
(e.g. wood then metal).
The following table offers some values, which are
for information only and may simplify the selection
of a sanding sheet
9
.
Wood Sanding sheet / Grit
Sanding of wood 40–240
Pre-sanding, e.g. of
rough, unplaned
beams and boards
40, 60
Surface sanding 80, 100, 120
Fine sanding of hard
woods
180, 240
- IAN 104446 1
- Table of contents 5
- General power tool 7
- 1. Work area safety 7
- 2. Electrical safety 7
- 3. Personal safety 7
- 4. Power tool use and care 8
- Appliance-specific 8
- Vacuuming dust 10
- Instructions, tips and tricks 10
- Maintenance and Cleaning 11
- Service centre 11
- Warranty 11
- Disposal 11
- Spis zawartości 12
- Ogólne wskazówki bezpie 15
- 3. Bezpieczeństwo osób 16
- 4. Staranne obchodzenie 16
- 5. Serwis 17
- Wskazówki bezpieczeństwa 17
- Wskazówki dotyczące pracy 19
- Konserwacja oraz czyszczenie 19
- Gwarancja 20
- Usuwanie do odpadów 20
- Tartalomjegyzék 22
- Bevezetés 24
- 5. Szervíz 27
- A rezgőcsiszolóra 27
- Munkára vonatkozó utalások 29
- Karbantartás és tisztítás 29
- Garancia 30
- Mentesítés 30
- Splošna varnostna navodila 35
- 1. Varnost na delovnem mestu 35
- 2. Električna varnost 35
- 3. Varnost oseb 35
- 5. Servis 36
- Varnostni napotki za napravo 36
- Originalni pribor / 37
- Vklop in izklop 37
- Nastavitev števila vibracij 38
- Pritrditev brusilnega papirja 38
- Sesanje prahu 38
- Delovni napotki, nasveti 38
- Vzdrževanje in čiščenje 39
- Garancija 39
- Odstranitev 40
- Garancijski list 41
- Seznam obsahu 43
- Všeobecné bezpečnostní poky 45
- 1. Bezpečnost na pracovišti 45
- 2. Elektrická bezpečnost 45
- 3. Bezpečnost osob 45
- 5. Servis 46
- Bezpečnostní pokyny 46
- Odsávání prachu 48
- Pracovní pokyny, tipy a triky 48
- Údržba a čištění 49
- Likvidace 50
- Zoznam obsahu 51
- Všeobecné bezpečnostné 53
- 2. Elektrická bezpečnosť 53
- 3. Bezpečnosť osôb 53
- Špecifické bezpečnostné pokyny 55
- Originálne príslušenstvo / 55
- Zapínanie a vypínanie 55
- Nastavenie počtu kmitov 56
- Upevnenie brúsneho listu 56
- Odsávanie prachu 56
- Pracovné pokyny, tipy a triky 56
- Údržba a čistenie 57
- Záruśná lehota 57
- Likvidácia 58
- Výrobca 58
- 59 DE/AT/CH 59
- Einleitung 61
- 62 DE/AT/CH 62
- 5. Service 63
- Gerätespezifische Sicherheits 63
- Bedienung 64
- Ein- und ausschalten 64
- Schwingzahl einstellen 64
- Schleifblatt befestigen 64
- Staub absaugen 64
- Wartung und Reinigung 65
- Garantie 66
- Entsorgung 66
- 67 DE/AT/CH 67
Verwandte Produkte und Handbücher für Schleifmaschinen Parkside PSS 250 A1
(63 Seiten)
(102 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.455 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern